Enable network policy support functionality

Enable policy, pod_label and namespace handlers to respond to network policy events. As this is not done by default you’d have to explicitly add that to the list of enabled handlers at kuryr.conf (further info on how to do this can be found at Containerized installation):

[kubernetes]
enabled_handlers=vif,lb,lbaasspec,policy,pod_label,namespace,kuryrnetwork,kuryrnetworkpolicy,kuryrport

Note that if you also want to enable prepopulation of ports pools upon new namespace creation, you need to also dd the kuryrnetwork_population handler (more details on How to enable ports pool support):

[kubernetes]
enabled_handlers=vif,lb,lbaasspec,policy,pod_label,namespace,kuryrnetworkpolicy,kuryrnetwork,kuryrnetwork_population,kuryrport

After that, enable also the security group drivers for policies:

[kubernetes]
service_security_groups_driver = policy
pod_security_groups_driver = policy

Warning

The correct behavior for pods that have no network policy applied is to allow all ingress and egress traffic. If you want that to be enforced, please make sure to create an SG allowing all traffic and add it to [neutron_defaults]pod_security_groups setting in kuryr.conf:

[neutron_defaults]
pod_security_groups = ALLOW_ALL_SG_ID

Enable the namespace subnet driver by modifying the default pod_subnet_driver option:

[kubernetes]
pod_subnets_driver = namespace

Select the subnet pool from where the new subnets will get their CIDR:

[namespace_subnet]
pod_subnet_pool = SUBNET_POOL_ID

Lastly, select the router where the new subnet will be connected:

[namespace_subnet]
pod_router = ROUTER_ID

Note you need to restart the kuryr controller after applying the above step. For devstack non-containerized deployments:

$ sudo systemctl restart devstack@kuryr-kubernetes.service

Same for containerized deployments:

$ kubectl -n kube-system get pod | grep kuryr-controller
$ kubectl -n kube-system delete pod KURYR_CONTROLLER_POD_NAME

For directly enabling the driver when deploying with devstack, you just need to add the policy, pod_label and namespace handler and drivers with:

KURYR_ENABLED_HANDLERS=vif,lb,lbaasspec,policy,pod_label,namespace,kuryrnetworkpolicy,kuryrport
KURYR_SG_DRIVER=policy
KURYR_SUBNET_DRIVER=namespace

Note

If the loadbalancer maintains the source IP (such as ovn-octavia driver), there is no need to enforce sg rules at the load balancer level. To disable the enforcement, you need to set the following variable:

KURYR_ENFORCE_SG_RULES=False

Testing the network policy support functionality

1. Given a yaml file with a network policy, such as:

   apiVersion: networking.k8s.io/v1
   kind: NetworkPolicy
   metadata:
     name: test-network-policy
     namespace: default
   spec:
     podSelector:
       matchLabels:
         project: default
     policyTypes:
     - Ingress
     - Egress
     ingress:
     - from:
       - namespaceSelector:
           matchLabels:
             project: default
       ports:
       - protocol: TCP
         port: 6379
     egress:
     - to:
       - namespaceSelector:
           matchLabels:
             project: default
       ports:
       - protocol: TCP
         port: 5978
   

2. Apply the network policy:

   $ kubectl apply -f network_policy.yml
   

3. Check that the resources has been created:

   $ kubectl get kuryrnetworkpolicies
   NAME                     AGE
   test-network-policy   2s
   
   $ kubectl get networkpolicies
   NAME                  POD-SELECTOR   AGE
   test-network-policy   role=db        2s
   
   $ openstack security group list | grep sg-test-network-policy
   | dabdf308-7eed-43ef-a058-af84d1954acb | sg-test-network-policy
   

4. Check that the rules are in place for the security group:

   $ kubectl get kuryrnetworkpolicy test-network-policy -o yaml
   
   apiVersion: openstack.org/v1
   kind: KuryrNetworkPolicy
   metadata:
     annotations:
       networkPolicyLink: <link>
     clusterName: ""
     creationTimestamp: 2018-10-02T11:17:02Z
     generation: 0
     name: test-network-policy
     namespace: default
     resourceVersion: "2117"
     selfLink: /apis/openstack.org/v1/namespaces/default/kuryrnetworkpolicies/test-network-policy
     uid: afb99326-c634-11e8-b63d-002564fdd760
   spec:
     egressSgRules:
     - sgRule:
         description: Kuryr-Kubernetes NetPolicy SG rule
         direction: egress
         ethertype: IPv4
         port_range_max: 5978
         port_range_min: 5978
         protocol: tcp
     ingressSgRules:
     - sgRule:
         description: Kuryr-Kubernetes NetPolicy SG rule
         direction: ingress
         ethertype: IPv4
         port_range_max: 6379
         port_range_min: 6379
         protocol: tcp
   status:
     securityGroupId: cdee7815-3b49-4a3e-abc8-31e384ab75c5
     securityGroupRules:
     …
   
   $ openstack security group rule list sg-test-network-policy --protocol tcp -c "IP Protocol" -c "Port Range" -c "Direction" --long
   +-------------+------------+-----------+
   | IP Protocol | Port Range | Direction |
   +-------------+------------+-----------+
   | tcp         | 6379:6379  | ingress   |
   | tcp         | 5978:5978  | egress    |
   +-------------+------------+-----------+
   

5. Create a pod:

   $ kubectl create deployment --image quay.io/kuryr/demo demo
   deployment "demo" created
   
   $ kubectl get pod -o wide
   NAME                    READY     STATUS    RESTARTS   AGE       IP
   demo-5558c7865d-fdkdv   1/1       Running   0          44s       10.0.0.68
   

6. Get the pod port and check its security group rules:

   $ openstack port list --fixed-ip ip-address=10.0.0.68 -f value -c ID
   5d29b83c-714c-4579-8987-d0c0558420b3
   
   $ openstack port show 5d29b83c-714c-4579-8987-d0c0558420b3 | grep security_group_ids
   | security_group_ids    | bb2ac605-56ff-4688-b4f1-1d045ad251d0
   
   $ openstack security group rule list bb2ac605-56ff-4688-b4f1-1d045ad251d0
   --protocol tcp -c "IP Protocol" -c "Port Range"
   +-------------+------------+-----------+
   | IP Protocol | Port Range | Direction |
   +-------------+------------+-----------+
   | tcp         | 6379:6379  | ingress   |
   | tcp         | 5978:5978  | egress    |
   +-------------+------------+-----------+
   

7. Try to curl the pod on port 8080 (hint: it won’t work!):

   $ curl 10.0.0.68:8080
   

8. Update network policy to allow ingress 8080 port:

   $ kubectl patch networkpolicy test-network-policy -p '{"spec":{"ingress":[{"ports":[{"port": 8080,"protocol": "TCP"}]}]}}'
   networkpolicy "test-network-policy" patched
   
   $ kubectl get knp test-network-policy -o yaml
   apiVersion: openstack.org/v1
   kind: KuryrNetworkPolicy
   metadata:
     annotations:
       networkPolicyLink: <link>
     clusterName: ""
     creationTimestamp: 2018-10-02T11:17:02Z
     generation: 0
     name: test-network-policy
     namespace: default
     resourceVersion: "1546"
     selfLink: /apis/openstack.org/v1/namespaces/default/kuryrnetworkpolicies/np-test-network-policy
     uid: afb99326-c634-11e8-b63d-002564fdd760
   spec:
     egressSgRules:
     - sgRule:
         description: Kuryr-Kubernetes NetPolicy SG rule
         direction: egress
         ethertype: IPv4
         port_range_max: 5978
         port_range_min: 5978
         protocol: tcp
     ingressSgRules:
     - sgRule:
         description: Kuryr-Kubernetes NetPolicy SG rule
         direction: ingress
         ethertype: IPv4
         port_range_max: 8080
         port_range_min: 8080
         protocol: tcp
   status:
     securityGroupId: cdee7815-3b49-4a3e-abc8-31e384ab75c5
     securityGroupRules:
     …
   
   $ openstack security group rule list sg-test-network-policy -c "IP Protocol" -c "Port Range" -c "Direction" --long
   +-------------+------------+-----------+
   | IP Protocol | Port Range | Direction |
   +-------------+------------+-----------+
   | tcp         | 8080:8080  | ingress   |
   | tcp         | 5978:5978  | egress    |
   +-------------+------------+-----------+
   

9. Try to curl the pod ip after patching the network policy:

   $ curl 10.0.0.68:8080
   demo-5558c7865d-fdkdv: HELLO! I AM ALIVE!!!
   

   Note the curl only works from pods (neutron ports) on a namespace that has the label project: default as stated on the policy namespaceSelector.

10. We can also create a single pod, without a label and check that there is no connectivity to it, as it does not match the network policy podSelector:

    $ cat sample-pod.yml
    apiVersion: v1
    kind: Pod
    metadata:
      name: demo-pod
    spec:
      containers:
      - image: quay.io/kuryr/demo
        imagePullPolicy: Always
        name: demo-pod
    
    $ kubectl apply -f sample-pod.yml
    $ curl demo-pod-IP:8080
    NO REPLY
    

11. If we add to the pod a label that match a network policy podSelector, in this case ‘project: default’, the network policy will get applied on the pod, and the traffic will be allowed:

    $ kubectl label pod demo-pod project=default
    $ curl demo-pod-IP:8080
    demo-pod-XXX: HELLO! I AM ALIVE!!!
    

12. Confirm the teardown of the resources once the network policy is removed:

    $ kubectl delete -f network_policy.yml
    $ kubectl get kuryrnetworkpolicies
    $ kubectl get networkpolicies
    $ openstack security group list | grep sg-test-network-policy