Floating IP via router interfaces¶

Problem Description¶

For some use cases [1], it can be useful to make floating IP translation happens on non-gateway router interfaces.

Proposed Change¶

Introduce “router-interface-fip” extension, which allows users to associate floating IPs via router interfaces.

Consider the topology like the following diagram. This extension allows to associate floating-ip-B to fixed-ip-X.

• floating-ip-A is created on network4.
• floating-ip-B is created on network3.
• Both of floating-ip-A and floating-ip-B are associated to fixed-ip-X.
• fixed-ip-Y and fixed-ip-Z don’t have any floating ip associations.

+-----------------------+
|  network4             |
|  (external=True)      |
+------------------+----+
                   |
                   |
                   |router gateway port
                   |(its primary address is gw-ip)
         +---------+--------------------------------------------+
         |      floating-ip-A                                   |
         |                                                      |
         |    router                                            |
         |    (enable_snat=True)                                |
         |                                                      |
         |                                        floating-ip-B |
         +----+-----------------+--------------------+----------+
              |router           |router              |router
              |interface        |interface           |interface
              |                 |                    |
              |                 |                    |
  +-----------+-----+    +------+----------+    +----+------------+
  | network1        |    | network2        |    | network3        |
  | (external=False)|    | (external=False)|    | (external=True) |
  +-----+-----------+    +--------+--------+    +------+----------+
        |                         |                    |
    +---+-------+             +---+-------+        +---+-------+
    |fixed-ip-X |             |fixed-ip-Y |        |fixed-ip-Z |
    +-----------+             +-----------+        +-----------+
       VM-X                      VM-Y                 VM-Z

In case multiple floating ip addresses are associated to a fixed ip address, a datapath should be careful which floating ip to use for SNAT:

• If there’s a floating ip associated via the egress port, either the router gateway port or a router interface, it should be used. For example, in the case of the above diagram, if VM-X sends a packet “fixed-ip-X -> fixed-ip-Z”, floating-ip-B, rather than floating-ip-A, should be used.
• Otherwise, if there’s a floating ip associated via the router gateway port, it should be used. For example, in the case of the above diagram, if VM-X sends “fixed-ip-X -> fixed-ip-Y”, floating-ip-A should be used.
• Otherwise, the datapath can choose arbitrary one.

A few interesting cases:

• If VM-Y sends a packet “fixed-ip-Y -> floating-ip-A”, it’s translated to “gw-ip -> fixed-ip-X” by the router and VM-X will receive it. This behaviour is not specific to this extension. See bug 1428887 [3] for the reason of the SNAT.
• If VM-Y sends a packet “fixed-ip-Y -> floating-ip-B”, it’s translated to “gw-ip -> fixed-ip-X” by the router and VM-X will receive it. However, its return traffic “fixed-ip-X -> gw-ip” will be translated to “floating-ip-A -> fixed-ip-Y” and probably will not be recognized as a return traffic by VM-Z’s network stack.
• If VM-Z sends a packet “fixed-ip-Z -> floating-ip-B”, it’s translated to “fixed-ip-Z -> fixed-ip-X” by the router and VM-X will receive it. While this case is very similar to the above cases, the SNAT should not be applied here. The datapath can distinguish these cases by the existance of the asssociation of a floating-ip via the router interface. (floating-ip-B) This behaviour is necessary for the primary use case. [1]
• If VM-Z sends a packet “fixed-ip-Z -> floating-ip-A”, it’s translated to “fixed-ip-Z -> fixed-ip-X” by the router and VM-X will receive it. However, its return traffic “fixed-ip-X -> fixed-ip-Z” will be translated to “floating-ip-B -> fixed-ip-Z” and probably will not be recognized as a return traffic by VM-Z’s network stack.

PREROUTING

    // floating ip dnat
    [per FIP]
    (dst) matches (fip) -> float dnat, ACCEPT

    // rev-snat for the default snat
    [if default SNAT is enabled on the router]
    (dst) matches (gw port ip) -> rev-snat, ACCEPT

    // rev-snat for MidoNet-specific "same subnet" rules
    [per RIF]
    (inport, dst) matches (rif, rif ip) -> rev-snat, ACCEPT

POSTROUTING

    // floating ip snat
    // multiple rules in order to implement priority (which FIP to use)
    // Note: "fip port" below is a router port, either the router gateway
    // port or router interface, which owns the corresponding FIP
    // configured.
    [per FIP]
    (outport, src) matches (fip port, fip) -> float snat, ACCEPT

    ----- ordering barrier

    [per FIP]
    (src) matches (fip) -> float snat, ACCEPT  // gateway port

    ----- ordering barrier

    [per FIP]
    (src) matches (fip) -> float snat, ACCEPT  // non gateway port

    ----- ordering barrier

    // do not apply default snat if it came from external-like network
    // (router interfaces with FIPs, and the gateway port)
    // Note: iptables based implementations need to "emulate" inport
    // match (eg. using marks in PREROUTING) as it isn't available
    // in POSTROUTING.
    [per FIP port]
    (inport) matches (fip port) -> ACCEPT
    [if default SNAT is enabled on the router]
    inport == the gateway port -> ACCEPT

    ----- ordering barrier

    // apply the default snat for the gateway port
    [if default SNAT is enabled on the router]
    outport == the gateway port -> default snat, ACCEPT

    // for non-float -> float traffic  (cf. bug 1428887)
    // "dst-rewritten" condition here means float dnat was applied in
    // prerouting.  in case of iptables based implementations,
    // "--ctstate DNAT" might be used.
    [if default SNAT is enabled on the router]
    dst-rewritten -> default snat, ACCEPT

    // MidoNet-specific "same subnet" rules
    [per RIF]
    (inport == outport == rif) && dst != 169.254.169.254
        -> snat to rif ip, ACCEPT

    // non-float -> non-float in tenant traffic would come here

References¶