Networking with neutron¶

SR-IOV¶

The SR-IOV specification defines a standardized mechanism to virtualize PCIe devices. This mechanism can virtualize a single PCIe Ethernet controller to appear as multiple PCIe devices. Each device can be directly assigned to an instance, bypassing the hypervisor and virtual switch layer. As a result, users are able to achieve low latency and near-line wire speed.

A full guide on configuring and using SR-IOV is provided in the OpenStack Networking service documentation

NUMA Affinity¶

As described in CPU topologies, NUMA is a computer architecture where memory accesses to certain regions of system memory can have higher latencies than other regions, depending on the CPU(s) your process is running on. This effect extends to devices connected to the PCIe bus, a concept known as NUMA I/O. Many Network Interface Cards (NICs) connect using the PCIe interface, meaning they are susceptible to the ill-effects of poor NUMA affinitization. As a result, NUMA locality must be considered when creating an instance where high dataplane performance is a requirement.

Fortunately, nova provides functionality to ensure NUMA affinitization is provided for instances using neutron. How this works depends on the type of port you are trying to use.

For SR-IOV ports, virtual functions, which are PCI devices, are attached to the instance. This means the instance can benefit from the NUMA affinity guarantees provided for PCI devices. This happens automatically.

For all other types of ports, some manual configuration is required.

1. Identify the type of network(s) you wish to provide NUMA affinity for.

   • If a network is an L2-type network (provider:network_type of flat or vlan), affinity of the network to given NUMA node(s) can vary depending on value of the provider:physical_network attribute of the network, commonly referred to as the physnet of the network. This is because most neutron drivers map each physnet to a different bridge, to which multiple NICs are attached, or to a different (logical) NIC.
   • If a network is an L3-type networks (provider:network_type of vxlan, gre or geneve), all traffic will use the device to which the endpoint IP is assigned. This means all L3 networks on a given host will have affinity to the same NUMA node(s). Refer to the neutron documentation for more information.

2. Determine the NUMA affinity of the NICs attached to the given network(s).

   How this should be achieved varies depending on the switching solution used and whether the network is a L2-type network or an L3-type networks.

   Consider an L2-type network using the Linux Bridge mechanism driver. As noted in the neutron documentation, physets are mapped to interfaces using the [linux_bridge] physical_interface_mappings configuration option. For example:

   [linux_bridge]
   physical_interface_mappings = provider:PROVIDER_INTERFACE
   

   Once you have the device name, you can query sysfs to retrieve the NUMA affinity for this device. For example:

   $ cat /sys/class/net/PROVIDER_INTERFACE/device/numa_node
   

   For an L3-type network using the Linux Bridge mechanism driver, the device used will be configured using protocol-specific endpoint IP configuration option. For VXLAN, this is the [vxlan] local_ip option. For example:

   [vxlan]
   local_ip = OVERLAY_INTERFACE_IP_ADDRESS
   

   Once you have the IP address in question, you can use ip to identify the device that has been assigned this IP address and from there can query the NUMA affinity using sysfs as above.

   Note

   The example provided above is merely that: an example. How one should identify this information can vary massively depending on the driver used, whether bonding is used, the type of network used, etc.

3. Configure NUMA affinity in nova.conf.

   Once you have identified the NUMA affinity of the devices used for your networks, you need to configure this in nova.conf. As before, how this should be achieved varies depending on the type of network.

   For L2-type networks, NUMA affinity is defined based on the provider:physical_network attribute of the network. There are two configuration options that must be set:

   [neutron] physnets

   This should be set to the list of physnets for which you wish to provide NUMA affinity. Refer to the documentation for more information.

   [neutron_physnet_{physnet}] numa_nodes

   This should be set to the list of NUMA node(s) that networks with the given {physnet} should be affinitized to.

   For L3-type networks, NUMA affinity is defined globally for all tunneled networks on a given host. There is only one configuration option that must be set:

   [neutron_tunneled] numa_nodes

   This should be set to a list of one or NUMA nodes to which instances using tunneled networks will be affinitized.

[neutron]
physnets = foo,bar

[neutron_physnet_foo]
numa_nodes = 0

[neutron_physnet_bar]
numa_nodes = 2, 3

[neutron_tunneled]
numa_nodes = 0