Create and distribute initial rings¶
Before starting the Object Storage services, you must create the initial account, container, and object rings. The ring builder creates configuration files that each node uses to determine and deploy the storage architecture. For simplicity, this guide uses one region and two zones with 2^10 (1024) maximum partitions, 3 replicas of each object, and 1 hour minimum time between moving a partition more than once. For Object Storage, a partition indicates a directory on a storage device rather than a conventional partition table. For more information, see the Deployment Guide.
Note
Perform these steps on the controller node.
Create account ring¶
The account server uses the account ring to maintain lists of containers.
Change to the /etc/swift directory.
Create the base account.builder file:
# swift-ring-builder account.builder create 10 3 1
Note
This command provides no output.
Add each storage node to the ring:
# swift-ring-builder account.builder \ add --region 1 --zone 1 --ip STORAGE_NODE_MANAGEMENT_INTERFACE_IP_ADDRESS --port 6202 \ --device DEVICE_NAME --weight DEVICE_WEIGHT
Replace STORAGE_NODE_MANAGEMENT_INTERFACE_IP_ADDRESS with the IP address of the management network on the storage node. Replace DEVICE_NAME with a storage device name on the same storage node. For example, using the first storage node in Install and configure the storage nodes with the /dev/sdb storage device and weight of 100:
# swift-ring-builder account.builder add \ --region 1 --zone 1 --ip 10.0.0.51 --port 6202 --device sdb --weight 100
Repeat this command for each storage device on each storage node. In the example architecture, use the command in four variations:
# swift-ring-builder account.builder add \ --region 1 --zone 1 --ip 10.0.0.51 --port 6202 --device sdb --weight 100 Device d0r1z1-10.0.0.51:6202R10.0.0.51:6202/sdb_"" with 100.0 weight got id 0 # swift-ring-builder account.builder add \ --region 1 --zone 1 --ip 10.0.0.51 --port 6202 --device sdc --weight 100 Device d1r1z2-10.0.0.51:6202R10.0.0.51:6202/sdc_"" with 100.0 weight got id 1 # swift-ring-builder account.builder add \ --region 1 --zone 2 --ip 10.0.0.52 --port 6202 --device sdb --weight 100 Device d2r1z3-10.0.0.52:6202R10.0.0.52:6202/sdb_"" with 100.0 weight got id 2 # swift-ring-builder account.builder add \ --region 1 --zone 2 --ip 10.0.0.52 --port 6202 --device sdc --weight 100 Device d3r1z4-10.0.0.52:6202R10.0.0.52:6202/sdc_"" with 100.0 weight got id 3
Verify the ring contents:
# swift-ring-builder account.builder account.builder, build version 4 1024 partitions, 3.000000 replicas, 1 regions, 2 zones, 4 devices, 100.00 balance, 0.00 dispersion The minimum number of hours before a partition can be reassigned is 1 The overload factor is 0.00% (0.000000) Devices: id region zone ip address port replication ip replication port name weight partitions balance meta 0 1 1 10.0.0.51 6202 10.0.0.51 6202 sdb 100.00 0 -100.00 1 1 1 10.0.0.51 6202 10.0.0.51 6202 sdc 100.00 0 -100.00 2 1 2 10.0.0.52 6202 10.0.0.52 6202 sdb 100.00 0 -100.00 3 1 2 10.0.0.52 6202 10.0.0.52 6202 sdc 100.00 0 -100.00
Rebalance the ring:
# swift-ring-builder account.builder rebalance Reassigned 1024 (100.00%) partitions. Balance is now 0.00. Dispersion is now 0.00
Create container ring¶
The container server uses the container ring to maintain lists of objects. However, it does not track object locations.
Change to the /etc/swift directory.
Create the base container.builder file:
# swift-ring-builder container.builder create 10 3 1
Note
This command provides no output.
Add each storage node to the ring:
# swift-ring-builder container.builder \ add --region 1 --zone 1 --ip STORAGE_NODE_MANAGEMENT_INTERFACE_IP_ADDRESS --port 6201 \ --device DEVICE_NAME --weight DEVICE_WEIGHT
Replace STORAGE_NODE_MANAGEMENT_INTERFACE_IP_ADDRESS with the IP address of the management network on the storage node. Replace DEVICE_NAME with a storage device name on the same storage node. For example, using the first storage node in Install and configure the storage nodes with the /dev/sdb storage device and weight of 100:
# swift-ring-builder container.builder add \ --region 1 --zone 1 --ip 10.0.0.51 --port 6201 --device sdb --weight 100
Repeat this command for each storage device on each storage node. In the example architecture, use the command in four variations:
# swift-ring-builder container.builder add \ --region 1 --zone 1 --ip 10.0.0.51 --port 6201 --device sdb --weight 100 Device d0r1z1-10.0.0.51:6201R10.0.0.51:6201/sdb_"" with 100.0 weight got id 0 # swift-ring-builder container.builder add \ --region 1 --zone 1 --ip 10.0.0.51 --port 6201 --device sdc --weight 100 Device d1r1z2-10.0.0.51:6201R10.0.0.51:6201/sdc_"" with 100.0 weight got id 1 # swift-ring-builder container.builder add \ --region 1 --zone 2 --ip 10.0.0.52 --port 6201 --device sdb --weight 100 Device d2r1z3-10.0.0.52:6201R10.0.0.52:6201/sdb_"" with 100.0 weight got id 2 # swift-ring-builder container.builder add \ --region 1 --zone 2 --ip 10.0.0.52 --port 6201 --device sdc --weight 100 Device d3r1z4-10.0.0.52:6201R10.0.0.52:6201/sdc_"" with 100.0 weight got id 3
Verify the ring contents:
# swift-ring-builder container.builder container.builder, build version 4 1024 partitions, 3.000000 replicas, 1 regions, 2 zones, 4 devices, 100.00 balance, 0.00 dispersion The minimum number of hours before a partition can be reassigned is 1 The overload factor is 0.00% (0.000000) Devices: id region zone ip address port replication ip replication port name weight partitions balance meta 0 1 1 10.0.0.51 6201 10.0.0.51 6201 sdb 100.00 0 -100.00 1 1 1 10.0.0.51 6201 10.0.0.51 6201 sdc 100.00 0 -100.00 2 1 2 10.0.0.52 6201 10.0.0.52 6201 sdb 100.00 0 -100.00 3 1 2 10.0.0.52 6201 10.0.0.52 6201 sdc 100.00 0 -100.00
Rebalance the ring:
# swift-ring-builder container.builder rebalance Reassigned 1024 (100.00%) partitions. Balance is now 0.00. Dispersion is now 0.00
Create object ring¶
The object server uses the object ring to maintain lists of object locations on local devices.
Change to the /etc/swift directory.
Create the base object.builder file:
# swift-ring-builder object.builder create 10 3 1
Note
This command provides no output.
Add each storage node to the ring:
# swift-ring-builder object.builder \ add --region 1 --zone 1 --ip STORAGE_NODE_MANAGEMENT_INTERFACE_IP_ADDRESS --port 6200 \ --device DEVICE_NAME --weight DEVICE_WEIGHT
Replace STORAGE_NODE_MANAGEMENT_INTERFACE_IP_ADDRESS with the IP address of the management network on the storage node. Replace DEVICE_NAME with a storage device name on the same storage node. For example, using the first storage node in Install and configure the storage nodes with the /dev/sdb storage device and weight of 100:
# swift-ring-builder object.builder add \ --region 1 --zone 1 --ip 10.0.0.51 --port 6200 --device sdb --weight 100
Repeat this command for each storage device on each storage node. In the example architecture, use the command in four variations:
# swift-ring-builder object.builder add \ --region 1 --zone 1 --ip 10.0.0.51 --port 6200 --device sdb --weight 100 Device d0r1z1-10.0.0.51:6200R10.0.0.51:6200/sdb_"" with 100.0 weight got id 0 # swift-ring-builder object.builder add \ --region 1 --zone 1 --ip 10.0.0.51 --port 6200 --device sdc --weight 100 Device d1r1z2-10.0.0.51:6200R10.0.0.51:6200/sdc_"" with 100.0 weight got id 1 # swift-ring-builder object.builder add \ --region 1 --zone 2 --ip 10.0.0.52 --port 6200 --device sdb --weight 100 Device d2r1z3-10.0.0.52:6200R10.0.0.52:6200/sdb_"" with 100.0 weight got id 2 # swift-ring-builder object.builder add \ --region 1 --zone 2 --ip 10.0.0.52 --port 6200 --device sdc --weight 100 Device d3r1z4-10.0.0.52:6200R10.0.0.52:6200/sdc_"" with 100.0 weight got id 3
Verify the ring contents:
# swift-ring-builder object.builder object.builder, build version 4 1024 partitions, 3.000000 replicas, 1 regions, 2 zones, 4 devices, 100.00 balance, 0.00 dispersion The minimum number of hours before a partition can be reassigned is 1 The overload factor is 0.00% (0.000000) Devices: id region zone ip address port replication ip replication port name weight partitions balance meta 0 1 1 10.0.0.51 6200 10.0.0.51 6200 sdb 100.00 0 -100.00 1 1 1 10.0.0.51 6200 10.0.0.51 6200 sdc 100.00 0 -100.00 2 1 2 10.0.0.52 6200 10.0.0.52 6200 sdb 100.00 0 -100.00 3 1 2 10.0.0.52 6200 10.0.0.52 6200 sdc 100.00 0 -100.00
Rebalance the ring:
# swift-ring-builder object.builder rebalance Reassigned 1024 (100.00%) partitions. Balance is now 0.00. Dispersion is now 0.00
Distribute ring configuration files¶
- Copy the account.ring.gz, container.ring.gz, and object.ring.gz files to the /etc/swift directory on each storage node and any additional nodes running the proxy service.
Except where otherwise noted, this document is licensed under Creative Commons Attribution 3.0 License. See all OpenStack Legal Documents.